Kwikset Deadbolt Wont Unlock : If the problem persists, check to make sure that the door and strike plate are not misaligned, that the deadbolt can lock and unlock without friction, .. Make sure the user code is correct and that the kwikset button is pushed after entering the user code. The lock jams and the turnpiece does not rotate. To get it open, you need to slide a sharp knife on top of the bolt. If the lcd lights up but the kwikset smartkey lock will not work; Sometimes the lock is stuck because the parts inside it have disengaged.
If the problem persists, check to make sure that the door and strike plate are not misaligned, that the deadbolt can lock and unlock without friction, . The lock jams and the turnpiece does not rotate. To get it open, you need to slide a sharp knife on top of the bolt. It could be that the connection between the main unit and the deadbolt unit is bad. While the door is open and unlocked, enter the following code to teach the lock the orientation of the door:
I couldn't get it to work (unlock and lock with my code) even after programming it until i opened the cover piece that goes over the batteries .
If successful, press the kwikset button. Press the lock button while the door is open and unlocked. While pulling the door hard enough to prevent the bolt from springing . While the door is open and unlocked, enter the following code to teach the lock the orientation of the door: Sometimes the lock is stuck because the parts inside it have disengaged. To get it open, you need to slide a sharp knife on top of the bolt. I couldn't get it to work (unlock and lock with my code) even after programming it until i opened the cover piece that goes over the batteries . The deadbolt latch does not extend or retract on its own during the door handing process. Remove the cover and battery pack from the lock and then make sure the door is open. If the problem persists, check to make sure that the door and strike plate are not misaligned, that the deadbolt can lock and unlock without friction, . Make sure the user code is correct and that the kwikset button is pushed after entering the user code. It could be that the connection between the main unit and the deadbolt unit is bad. If the latch bolt does not extend to lock, then all codes have been.
The deadbolt latch does not extend or retract on its own during the door handing process. Remove the cover and battery pack from the lock and then make sure the door is open. Sometimes the lock is stuck because the parts inside it have disengaged. It could be that the connection between the main unit and the deadbolt unit is bad. Make sure the user code is correct and that the kwikset button is pushed after entering the user code.
If the problem persists, check to make sure that the door and strike plate are not misaligned, that the deadbolt can lock and unlock without friction, .
Remove the cover and battery pack from the lock and then make sure the door is open. While pulling the door hard enough to prevent the bolt from springing . Press the lock button while the door is open and unlocked. I couldn't get it to work (unlock and lock with my code) even after programming it until i opened the cover piece that goes over the batteries . Make sure the user code is correct and that the kwikset button is pushed after entering the user code. If the lcd lights up but the kwikset smartkey lock will not work; To remedy the situation, perform the handing process again. Sometimes the lock is stuck because the parts inside it have disengaged. While the door is open and unlocked, enter the following code to teach the lock the orientation of the door: If the problem persists, check to make sure that the door and strike plate are not misaligned, that the deadbolt can lock and unlock without friction, . It could be that the connection between the main unit and the deadbolt unit is bad. Take a small hammer to the body surrounding the keyhole. The lock jams and the turnpiece does not rotate.
If successful, press the kwikset button. The deadbolt latch does not extend or retract on its own during the door handing process. If the latch bolt does not extend to lock, then all codes have been. To get it open, you need to slide a sharp knife on top of the bolt. Sometimes the lock is stuck because the parts inside it have disengaged.
If the lcd lights up but the kwikset smartkey lock will not work;
Make sure the user code is correct and that the kwikset button is pushed after entering the user code. While pulling the door hard enough to prevent the bolt from springing . If the door still won't unlock, use a key to unlock the . If the problem persists, check to make sure that the door and strike plate are not misaligned, that the deadbolt can lock and unlock without friction, . To get it open, you need to slide a sharp knife on top of the bolt. Press the lock button while the door is open and unlocked. If the latch bolt does not extend to lock, then all codes have been. It could be that the connection between the main unit and the deadbolt unit is bad. The lock jams and the turnpiece does not rotate. I couldn't get it to work (unlock and lock with my code) even after programming it until i opened the cover piece that goes over the batteries . While the door is open and unlocked, enter the following code to teach the lock the orientation of the door: If the lcd lights up but the kwikset smartkey lock will not work; Sometimes the lock is stuck because the parts inside it have disengaged.